Cleaning and Damage Restoration in Gahanna

We provided a comprehensive mold remediation, moisture assessment, and containment solution to safeguard the new homeowners' indoor living environment. Our technicians established critical containment and set up HEPA-filtered air scrubbers to capture airborne spores during the remediation process. We conducted precision moisture tracking across the ceiling and wall cavities to determine the extent of moisture migration from the attic space above. We then safely removed the contaminated, deteriorated drywall and plaster sections along the upper wall seam, performed HEPA vacuuming of the exposed structural framing, and applied an EPA-registered antimicrobial biocide to eradicate fungal roots and prevent future mold growth prior to drywall reconstruction.

We executed a complete bathroom put-back, drywall repair, and surface finishing solution to restore the space to pre-loss condition. Our technicians scraped away loose, delaminated plaster and peeling paint down to a sound substrate, thoroughly sanitising the affected area with an EPA-registered antimicrobial wash. We hung fresh moisture-resistant drywall boards where required, skim-coated the wall and ceiling transitions with setting-type joint compound, and hand-sanded the entire surface flush with the existing tile line. Finally, we applied a mold-inhibiting, high-adhesion primer across the repaired upper walls and ceiling to seal out bathroom moisture and prepare the room for durable topcoat painting.

Our restoration team inspected the interior damage and the attic space, identifying the compromised ceiling plasterboard and severe water staining along the timber roof decking. To halt further water ingress before the final interior 'put back' and structural repairs could commence, our exterior crew safely navigated the asphalt shingle roof to reposition and securely fasten an emergency weatherproof tarp over the compromised area.

Our team expertly addressed the basement water loss by performing targeted demolition, including cutting into the ceiling to access water-affected areas and removing sections of the damaged walls. This process exposed insulation and structural elements, allowing for thorough drying, remediation of water-damaged materials, and preparation for reconstruction to restore the basement to its original condition.

Our exterior repair technicians safely accessed the roofline, realigned the loose vinyl siding panels, and securely refastened them into their locking channels, ensuring the exterior wall remains fully weatherproofed and visually restored to its original condition.

Our team provided prompt water removal services and identified and addressed the source of the water intrusion to prevent recurrence. We cleared out all wet debris and contaminated materials, followed by thorough cleaning and treatment of all affected surfaces. Specialized drying equipment was then deployed to eliminate excess moisture and stabilize the crawlspace environment, successfully restoring the basement to a clean, dry, and safe condition.

Teasdale-Fenton Columbus provided expert ceiling repair, which included patching and preparing the damaged area for a smooth finish. The team meticulously taped off the ceiling and protected surrounding surfaces with plastic sheeting to ensure precise paint lines and prevent any damage. After completing the painting, all equipment was removed, and the area was thoroughly cleaned and returned to its original state, ensuring the customer's satisfaction with the 'put back' aspect of the service.

Our exterior maintenance team prepared the site by positioning extension ladders safely along the brick exterior, carefully inspected and repaired the damaged timber and protective overhang components to ensure structural integrity and proper roofline ventilation, and completed the project by tidying the work area and leaving the property fully restored and protected against weather elements.

We provided a comprehensive ceiling reconstruction and structural put-back solution to restore the room to pre-loss condition. Our technicians first cleared away the fallen plaster, drywall remnants, and ruined insulation debris, safely prepping the surrounding perimeter and framing. We inspected the exposed wooden roof rafters and framing to confirm all structural elements were dry and sound. Next, we installed fresh, properly sized CertainTeed kraft-faced fiberglass batt insulation between the ceiling joists, securing the vapor barrier with precise stapling to ensure complete thermal efficiency and moisture control. Finally, we squared off the perimeter drywall seams to prepare the ceiling plane for hanging new gypsum wallboard, taping, mudding, and finishing.

Our team executed an efficient commercial water damage restoration protocol, which included assessing the moisture migration and performing targeted flood cuts to remove contaminated drywall and baseboards. Following the complete structural drying of the wall cavities and carpets using industrial air movers, we executed a comprehensive "put back" service to fully rebuild and restore the affected areas. This reconstruction process involved installing new drywall, replacing the baseboards, reinstalling the cabinetry, and returning the commercial workspace to its pre-loss condition.

Our mitigation specialists utilised a ladder to safely access the attic space and perform a comprehensive moisture and mould inspection. We documented significant black and white fungal growth spreading across the timber roof decking—a direct result of prolonged water intrusion from an active leak—and formulated a detailed remediation plan to eradicate the mould and restore the structural wood once the roof is repaired.

We provided a comprehensive commercial door put-back, hardware restoration, and realignment solution to restore full functionality and security. Our technicians conducted a structural inspection of the metal door frame and edge mortise, removing corroded components and cleaning out accumulated debris around the latch pocket. We reseated and leveled the UL-listed automatic flush bolt assembly, securing it firmly into the metal door channel with heavy-duty commercial fasteners. We then realigned and reinforced the header strike plate on the upper door frame to ensure seamless engagement with the latch bolt. Finally, we adjusted the door swing and latch clearance, thoroughly testing the automatic locking mechanism to guarantee smooth operation, secure latching, and full building code compliance.