Carpet and Floor Cleaning and Damage Cleanup in Columbus

We provided a comprehensive exterior siding repair, weatherproofing, and reconstruction estimate. Our technicians inspected the wall elevation around the newly installed electrical disconnect panel to assess heat damage and siding cut-outs. We scoped the removal and detachment of melted and altered vinyl siding courses, prepped the exposed structural insulation board with proper weather-resistive flashing, and measured for matching replacement vinyl siding panels. Furthermore, we planned for custom J-channel trim fabrication around the utility boxes and electrical conduits to ensure an airtight, watertight seal, followed by a light chemical wash of the adjacent wall elevation to blend the repair seamlessly.

We provided a comprehensive structural put-back and interior repair solution. Our technicians squared off the damaged openings in the textured ceiling, installed wood backing supports, and hung fresh drywall patches, finishing with taping, mudding, and custom texture matching to blend with the existing ceiling pattern. On the flooring, we removed damaged tack strips, prepped the exposed concrete threshold, and installed matching transition strips between the parquet flooring and the adjacent storage room to ensure a safe, flush, and finished entryway.

Our team provided a comprehensive, multi-phase mold remediation and environmental stabilization solution. Our team first isolated the affected zones with critical plastic containment barriers and set up commercial HEPA air scrubbers under negative pressure to capture airborne spores and prevent cross-contamination. After safely removing non-salvageable peeling ceiling debris and saturated materials, technicians performed thorough HEPA vacuuming across all drywall and wood surfaces. We then conducted a deep antimicrobial wash using EPA-registered broad-spectrum biocides on the contaminated wall cavities, plumbing recesses, and structural framing studs. Finally, we deployed commercial dehumidifiers to eliminate residual moisture pockets and applied an antimicrobial encapsulation sealant over the cleaned drywall and framing to permanently inhibit future microbial growth.

We executed a comprehensive interior carpentry restoration and put-back solution to restore the door frame to pre-loss condition. Our technicians pulled exposed finishing nails, sanded damaged rough framing, and cleaned out the recessed casing margins. We measured, cut, and installed matching replacement wood door trim and casing along the doorway perimeter, securing it firmly to the structural wood studs. We then repaired splintered jamb corners using high-grade wood filler and structural epoxy, caulked all trim seams flush with the surrounding drywall, and prepped the new trim with primer and matching interior paint for a seamless finish.

We provided a comprehensive commercial door put-back, hardware restoration, and realignment solution to restore full functionality and security. Our technicians conducted a structural inspection of the metal door frame and edge mortise, removing corroded components and cleaning out accumulated debris around the latch pocket. We reseated and leveled the UL-listed automatic flush bolt assembly, securing it firmly into the metal door channel with heavy-duty commercial fasteners. We then realigned and reinforced the header strike plate on the upper door frame to ensure seamless engagement with the latch bolt. Finally, we adjusted the door swing and latch clearance, thoroughly testing the automatic locking mechanism to guarantee smooth operation, secure latching, and full building code compliance.

We provided a comprehensive water damage mitigation, controlled demolition, and structural drying solution to stabilize the utility space. Following confirmation that the overhead leak source was repaired, our technicians safely contained the closet and carefully demolished the saturated ceiling drywall and vertical wall assemblies to fully expose the structural framing, floor joists, and electrical conduits. We conducted detailed moisture tracking throughout the wall studs and applied an EPA-registered antimicrobial treatment across all exposed framing to prevent mold and bacterial growth. Finally, we staged commercial low-profile air movers and high-capacity LGR dehumidifiers directly in the utility closet to establish a high-velocity drying vortex, aggressively pulling bound moisture out of the framing timber and concrete subfloor before drywall reinstallation.

We provided a comprehensive ceiling reconstruction and structural put-back solution to restore the room to pre-loss condition. Our technicians first cleared away the fallen plaster, drywall remnants, and ruined insulation debris, safely prepping the surrounding perimeter and framing. We inspected the exposed wooden roof rafters and framing to confirm all structural elements were dry and sound. Next, we installed fresh, properly sized CertainTeed kraft-faced fiberglass batt insulation between the ceiling joists, securing the vapor barrier with precise stapling to ensure complete thermal efficiency and moisture control. Finally, we squared off the perimeter drywall seams to prepare the ceiling plane for hanging new gypsum wallboard, taping, mudding, and finishing.

Our team executed a comprehensive exterior entryway restoration and structural put-back solution. Our team inspected and realigned the heavy-duty metal door slab, securing the door-mounted reinforcement brackets and hardware to ensure smooth, secure operation. We cleaned and prepped the door surface to remove impact scuffs, repaired the deteriorated exterior trim and door frame base, and re-caulked and weathersealed the aluminum threshold against the concrete walkway to prevent water seepage and eliminate drafts.

We provided a comprehensive exterior wood restoration, surface prep, and finishing put-back service. Our technicians began by scraping away all loose, flaking, and peeling paint from the wooden deck fascia, header beams, and handrail tops. We sanded the exposed timber surfaces smooth to remove weather-damaged wood fibers, prepped the surrounding siding and concrete areas, and applied a durable, weather-resistant primer and protective exterior coating package to safeguard the structure against future moisture damage and restore its aesthetic appearance.

Our mitigation specialists accessed the unfinished basement via the exterior cellar doors to conduct a comprehensive moisture and mould inspection. We identified significant, fuzzy black mould growth on discarded timber and debris resting on the concrete floor as a direct result of the recent water ingress. We proceeded to safely remove and dispose of the contaminated materials, applied professional-grade antimicrobial treatments to the affected concrete surfaces, and implemented a structural drying plan to halt further fungal development and restore the property to a safe standard.

Our exterior repair team performed targeted demolition to remove the compromised siding and window trim, safely extracted the severely rotted structural framing that had become conducive to wood-destroying organisms, and executed a complete structural rebuild ("put back") utilizing treated lumber, finalizing the project by repairing the damaged downspout to ensure water is properly diverted away from the foundation.

Our mitigation experts conducted a thorough diagnostic moisture inspection, utilizing a digital moisture meter on the affected interior ceiling to map the extent of the water intrusion, and subsequently tracked the moisture path up into the attic space where we identified significant water staining on the plywood roof decking, allowing us to pinpoint the source of the active roof leak and formulate a comprehensive mold remediation and structural drying plan.